P1X Pro Front Mount: Installation and Compatibility Guide
By Sim-Lab - Making motorsports accessible | Published: 2026-10-24
Category: How-to Guides
Learn how to install the P1X Pro Front Mount on your Sim-Lab or 8020 cockpit, including compatibility checks and step-by-step instructions.
Quick answer
The P1X Pro Front Mount fits Sim-Lab P1X PRO, P1X Ultimate, P1X, and P1 cockpits, plus most third-party 8020 rigs. Installation involves attaching the mount to the wheel deck and securing your wheelbase with the correct bolts.
Why compatibility matters before you start
The P1X Pro Front Mount is designed to work with a wide range of wheelbases, including Sim-Lab DDS26 TorqueSync, Sim-Lab DDS39 TorqueSync, Bodnar 50 series, Lenze MCS12 series, MiGe 130ST (small and big), Simagic Alpha Mini DD and Ultimate, Simucube 2 and Simucube 3 Sport/Pro/Ultimate, VNM wheelbases, VRS DFP15, and VRS DFP20/uDFP20. However, not every wheelbase uses the same bolt pattern or mounting hole spacing. Before you begin, verify that your wheelbase is listed or measure the hole pattern to avoid wasted effort.
If your wheelbase is not listed, you may need an adapter plate or a different mount. The front mount is not universal—it relies on four M6 bolts that align with standard 8020 slot spacing, so non-standard patterns won't fit without modification.
Tools and parts you will need
You will need the P1X Pro Front Mount itself, four M6 bolts (typically included), a 5 mm hex key, and a torque wrench if you want to tighten to spec. If you are mounting to a third-party 8020 cockpit, ensure your profile slots are clean and free of debris. For Sim-Lab cockpits, the mount bolts directly into the wheel deck without extra brackets.
Installation steps
- Step 1: Prepare the cockpit: Remove any existing wheel deck or mount from your cockpit. Clean the 8020 profile slots where the front mount will attach. Check that the slots are free of debris and that the T-nuts (if using) slide smoothly. Common mistake: Forgetting to remove old T-nuts or brackets can cause misalignment. Double-check that the mounting surface is flat and clean.
- Step 2: Attach the front mount to the wheel deck: Position the P1X Pro Front Mount on the wheel deck so that the four mounting holes align with the 8020 slots. Insert the M6 bolts through the mount and into the T-nuts or threaded holes. Tighten each bolt gradually in a cross pattern to ensure even pressure. Common mistake: Overtightening one bolt before the others can warp the mount or strip threads. Use a 5 mm hex key and tighten evenly.
- Step 3: Mount your wheelbase: Place your wheelbase onto the front mount, aligning the mounting holes with the slots on the mount. Use the bolts provided with your wheelbase (or the M6 bolts if compatible) to secure it. Tighten to the manufacturer's recommended torque, typically 8–10 Nm for most wheelbases. Common mistake: Using bolts that are too long can damage the wheelbase internals. Check bolt length against the mount thickness before tightening.
- Step 4: Check alignment and test: Once everything is tightened, check that the wheelbase is level and centered. Rotate the wheel by hand to ensure there is no binding or interference with the mount. If using a direct-drive wheelbase, power it on and run a quick calibration. Common mistake: Skipping the manual rotation check can lead to binding that damages the wheelbase over time. Always verify free movement before powering on.
Product facts
- P1X Pro Front Mount: The P1X Pro Front Mount is designed for use with P1X PRO, P1X Ultimate, P1X, and P1 cockpits, as well as most third-party 8020 cockpits. This means you can use it on many existing rigs without needing a custom adapter, but you should still verify your cockpit's profile size (typically 8020 series) before ordering.
P1X Pro Front Mount
