VARIO VESA Adapter Kit: Mounting and Compatibility Guide

By Sim-Lab - Making motorsports accessible | Published: 2026-10-20

Category: How-to Guides

Learn how to install and use the VARIO VESA Adapter Kit for precise monitor alignment in your sim racing rig. Covers compatibility, setup steps, and common pitfalls.

Quick answer

The VARIO VESA Adapter Kit lets you fine-tune monitor height and rotation in two planes using an Allen key, making it ideal for aligning triple-screen setups on a sim racing rig.

Why the VARIO VESA Adapter Kit is a smart upgrade

If you've mounted monitors directly to a VESA plate, you know how frustrating it is to get the height and angle exactly right. The VARIO VESA Adapter Kit solves this with a patented mechanism that allows 32 mm of vertical adjustment and ±10 mm horizontal adjustment, plus ±5 degrees of rotation in both planes. This means you can align your screens perfectly without shims or guesswork.

The kit is sold as a set of three brackets, which is ideal for triple-monitor setups, or as a single bracket if you only need to tweak one display. It's compatible with standard VESA mounting patterns, so it works with most sim racing monitor mounts and freestanding stands from Sim-Lab and other brands.

Compatibility considerations

Before you start, check that your monitor mount has a standard VESA plate (75x75 mm or 100x100 mm) and that the adapter's adjustment range fits your screen's weight and size. The kit is designed for monitors up to about 10 kg per bracket, but heavier screens may require a more rigid mount. If your mount is a freestanding triple stand like the Sim-Lab Varior Triple Mount, the adapter integrates seamlessly. For desk-mounted arms, the extra height adjustment can help center the screen vertically.

One limitation: the adapter adds about 20 mm of depth between the mount and the monitor, so if your rig has tight clearance behind the screens, measure first. The adjustment range is modest—32 mm vertical and ±10 mm horizontal—so it's meant for fine-tuning, not major repositioning.

How to install the VARIO VESA Adapter Kit

1. Remove the monitor from its current mount: Unplug the monitor and lay it face-down on a soft surface. Remove the four VESA screws holding it to your existing mount or stand. Keep the screws safe—you'll reuse them to attach the adapter. Common mistake: Forgetting which screws go where. Lay them out in order or take a photo before disassembly.
2. Attach the VARIO VESA Adapter to the monitor: Position the adapter bracket over the VESA holes on the back of the monitor. Use the screws that came with your monitor or the ones from the kit (if compatible). Tighten them firmly but don't overtighten—you want the bracket to sit flush. Check that the adapter's adjustment slots face outward so you can access the Allen key later.
3. Mount the adapter to your monitor stand: Align the adapter's mounting holes with the VESA plate on your rig's monitor mount. Insert the supplied bolts and tighten them with the Allen key. Make sure the adapter is level before fully tightening. If the adapter doesn't sit flat, loosen the bolts and re-align. A tilted base will throw off your final adjustment.
4. Fine-tune height and rotation: Use the Allen key to adjust the vertical position (32 mm range) and horizontal offset (±10 mm). Then tweak the rotation in both planes (±5 degrees each) until the monitor aligns with your other screens or your seated eye line. Work in small increments—tighten the adjustment screws slightly after each change to hold the position while you check alignment.
5. Repeat for additional monitors and finalize: If you're setting up a triple-screen rig, repeat steps 1-4 for each monitor. Once all screens are aligned, double-check all bolts are tight and the cables aren't pinched. Power on and test the view from your driving position. Final check: Sit in your rig and look at the bezel gaps. If one screen is slightly off, a small tweak to the rotation screw often fixes it without redoing the whole mount.

Product in focus

VARIO™ VESA Adapter Kit: Fine-tune the alignment of your monitors with our patented VARIO Vesa adapter kit. The simple but highly efficient mechanism allows you to adjust the height and rotation angles in 2 planes with an Allen key. Vertical adjustment possible of 32 mm, horizontal adjustment +/- 10 mm, horizontal rotation +/- 5 deg, vertical rotation +/- 5 deg. This means you can dial in the perfect monitor alignment for an immersive sim racing view without needing extra shims or tools beyond a single Allen key.
VARIO™ VESA Adapter Kit